960 Project Pt. 4 - End of Spring Almost Summer Updates

Since my last update back in February, I have had a lot of changes happen in my life. I went from an office job, to working full time for a local Volvo shop. I now do the marketing and classic car & car parts sales for Hailey Import Service. Due to this, I have been busy but lots of mods have been happening to my 960. My last update I had done a few comfort modifications, but I have upgraded the car even further. The car got a new dash carpet, full steam clean (again), and some much better air fresheners to remove the old musty smell. Using the ozone generator followed by an order remover disk I was able to neutralize the mold smell caused by the water leaks in the car. A re-sealed sunroof has also helped reduce water entry into the car.

Over the past few months, I have been driving the car on an almost daily basis, slowly building up a trust in its reliability. I have been able to do 2 round trips to visit my family in Charleston, SC and the car had no hiccups from the 4 hour drive each way.

Safety has also been improved with new lighting and taillights. I used LED upgrades in the lights and the difference was significant. Fahren LEDs were used for the headlights, and SNGL LEDs were used for the fog lights. Both kits were ordered with a 6600k color tone to give the car a clean white look up front.

One of the major issues I have had with this car have been the abused cosmetics. The paint is in rough shape in a lot of locations around the car, and does show signs of a respray at some point. During a washing session, the power washer took the paint on the rear drivers door clean off revealing a white door underneath. Since then I have begun the process of using vinyl wrap to cover the worst affected panels on the car. Avery gloss black has been used due to its cheap price, as well as its very close color match to Volvo 019 black color code.

Side shot showing the painted drivers door vs. the wrapped rear door.

The hood before. Note the clear coat spots and “crows feet” marks.

After, not 100% color accurate but much better.

Other additions to the car have mostly been cosmetic. A set of used corner lights from the UK were imported. I have always liked the clean look of clear lights up front. The set cost me about $80 when all said and done. Expensive, but around the going rate for a set in the US. A bonus was that they came with the sockets for a single filament bulb instead of dual like ours require.

960 Project Pt. 3 - Always Remember Your Oil

Its the new year, and progress has finally been made in the drive-ability of the 960. Over the past few months I have been slowly accumulating parts to fix all the small issues with the car. I was finally able to take a whole day and get the car up on a lift. I want to make a special thank you to Haileys Import Service in Greensboro, NC, who I have been going to for a while with my Volvos. They let me have access to their shop, tools, and a lift to get everything done on the 960 sand saved me likely days of work. They also helped me procure a new 960 seat from an S90 which fits perfectly in the car (well its the wrong color, but hey its not ripped, and actually moves!)

Let start off with the seat, this was a whole process, but surprisingly cheap to do. I saw my local LKQ had a nice Volvo S90 in the yard, and I was able to get to it very quickly to aquire a new seat. The removal process was fairly standard, and only takes 4 bolts and a few electrical connectors to remove. I found the hardest part was lining the “plugs” up to take the seat out of the rails. The seat uses a similar system to what you would see on an old hotel door lock chain, where it slides into a hole then down the rail where it is locked into place. Getting the seat in the right place to get it out of these holes is a painful experience and requires a lot of pushing and pulling on the seat.

For an LKQ car I was genuinely surprised at the quality of the interior. Usually these cars are absolutely wrecked, then again this one did have a pretty serious water leak beginning to develop unfortunately. Once I was able to get it back to the shop, installation was very easy, and I am disapointed I didnt get a picture of my old drivers seat since it was in quite the state.

A rogue golf tee, some candy wrappers, and a quarter. My “bounty” found under the seat.

After removing the seat, it made more sense to me why mold had begun to grow on the center console. I was able to take care of the mold with a bleached cloth, as well as a slew of degreasers and cleaners. An ozone generator is going to be used in the car for good measure.

The next steps were mostly mechanical fixes. For a long time, the car has been leaking power steering fluid. I was able to track this back to a leaking return line (non pressurized). You will see in the picture that the hose I removed was original and even had the late 1996 printing date on it. Volvo sells OEM replacement hose, and other than the mess that the fluid made coming out, the replacement process is as easy as undoing 2 hose clamps and taking off the hold hose. I found removing the bottom first was easier due to being able to pull up on it, but removing the hose from the reservoir require some special tools that could pry the hose away from the flange.

The ends of the old hose were super tight from 23 years of being installed.

Keep in mind the hose is cut to fit, so some trimming will be needed. Some new ATF was poured into the system, and the bubbles burped out by giving the rack a few back and forth movements with the steering wheel.

The last handful of fixes were around the front suspension area. New Lemforder end links were installed with ease, and helped the handling of the car significantly. The old end links had insane amounts of play, and I do not doubt that they were original 1997 equipment. They were work enough that they had almost 0 resistance and could be freely moved around in their joints. Additionally, new brake rotors were installed, and the old pads were sanded down to give them a fresh face.